[Nagiosplug-devel] check_nrpe question

[Thomas Guyot-Sionnest]

I had the same problem but in in a different context. I'm not sure it it
will help, but try:
- replacing the \ by $ ('$$' instead of '\$')
- removing the \ before the $
- Each change above while enclosing the service list in single quotes ([...]
-l 'serv1,serv$$23,etc' [...])

As a last resort you could add a comma at the end of the list, so all checks
will be performed but you will allways see something like ": Unknown".
Return status should be ok as well.

Good luck...

Thomas

> -----Original Message-----
> From: nagiosplug-devel-bounces at lists.sourceforge.net 
> [mailto:nagiosplug-devel-bounces at lists.sourceforge.net] On 
> Behalf Of Gary W. Smith
> Sent: September 19, 2006 14:34
> To: nagiosplug-devel at lists.sourceforge.net
> Subject: [Nagiosplug-devel] check_nrpe question
> 
> I have a nagios server that makes a call to a server running 
> nrpe to collect data.  The server running nrpe itself uses 
> check_nt to collect some data from some Wintel boxes behind 
> it's firewall.  
> 
> The nrpe server has the following command in place on the 
> remote nrpe server.
> 
> command[check_data_01_services]=/usr/lib/nagios/plugins/check_
nt -H 10.94.64.4 -p 8244 -v SERVICESTATE -d SHOWALL -l >
MSExchangeIS,MSExchangeMGMT,MSExchangeMTA,MSExchangeSA,RESvc,M
> SSQL\$ATACENTER,SMTPSVC,SPTServer,W3SVC,lanmanserver,BackupExe
> cAgentAccelerator,IISADMIN,Spooler
> 
> This command when executed on the nagios box reports all 
> okay.  All seems good there.
> 
> On the nagios server I call the remote nrpe command and I get 
> the following error.
> 
> /usr/lib/nagios/plugins/check_nrpe -H REMOTEHOST -p 
> REMOTEPORT -c check_data_01_services
> 
>  MSExchangeIS: Started - MSExchangeMGMT: Started - 
> MSExchangeMTA: Started - MSExchangeSA: Started - RESvc: 
> Started - MSSQL$ATACENTER: Started - SMTPSVC: Started - 
> SPTServer: Started - W3SVC: Started - lanmanserver: Started - 
> BackupExecAgentAccelerator: Started - IISADMIN: Started - 
> Spooler$: Unknown
> 
> Note the $ after spooler.  Even if I remove spooler from the 
> nrpe config file it then dies on IISADMIN, etc.  I have 3 
> other servers that I check in the same way without any 
> siginificant problem.  
> 
> 
> Here is the configuration portion of nagios.
> 
> define service {
> 
>     service_description              Service State
> 
>     use                              generic-service
> 
>     host_name                        REMOTEHOSTNAME
> 
>     check_command                    check_nrpe!check_data_01_services
> 
> }
> 
> define service {
> 
>     name                             generic-service
> 
>     is_volatile                      0
> 
>     check_period                     24X7
> 
>     max_check_attempts               5
> 
>     normal_check_interval            30
> 
>     retry_check_interval             1
> 
>     active_checks_enabled            1
> 
>     passive_checks_enabled           1
> 
>     parallelize_check                1
> 
>     obsess_over_service              1
> 
>     check_freshness                  1
> 
>     freshness_threshold              0
> 
>     notifications_enabled            1
> 
>     notification_interval            120
> 
>     notification_period              24X7
> 
>     notification_options             u,c,w,r
> 
>     event_handler_enabled            1
> 
>     flap_detection_enabled           1
> 
>     low_flap_threshold               0
> 
>     high_flap_threshold              0
> 
>     process_perf_data                1
> 
>     retain_status_information        1
> 
>     retain_nonstatus_information     1
> 
>     contact_groups                   all-admins
> 
>     register                         0
> 
> }
> 
> Any ideas?
> 
> 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/x-pkcs7-signature
Size: 3022 bytes
Desc: not available
URL: <http://nagios-plugins.org/archive/devel/attachments/20060919/271b9c4b/attachment.bin>